Hello Folks, I am new here.

I would like to install MorphOS on an X5000 but I am stuck.

A couple of years back I had a USB or a DVD and used MorphOS now and then, but I never managed to install it to the internal storage. That's why I never bought a license.
Since then I did not change anything hardware wise.

Yesterday I downloaded version 3.20 and successfully wrote the image on a USB stic using "rawwrite", however I can not boot the system. These lines appear on the screen:

MirphOS boot loader version 1.17
Select a boot partition:
* 1. HDIMG0: (boot priority 15)
2. DH0: (boot priority 0)
3. DH1: (boot priority -1)
Timeout, booting from HDIMG0:
Trying to load "bootcyrusplus.img" from "HDIMG0:"....
Loaded "bootcyrusplus.img" from "HDIMG0:", booting...

And then it stops there.

I can reset the system using CTRL-Amiga-Amiga, so apparently the system does not freeze.

I re-wrote the image to the USB using "dd" this time, but the results are the same.

Any idea what I am doing wrong?

Unfortunately I can not burn a DVD in order to try out the liveCD.

Any help appreciated!

Murphy.

Might help if you would specify the exact config, which GPU what kinda drives and so on.

Or just try another USB stick which might make a difference as it seems to fail at a point where MorphOS takes over from the bootloader.

If you have 2 Radeon cards, the other one may be picked up by MorphOS now - and if that one is connected via DP it wouldn't work. That port isn't supported at all.

@Murphy

We have already discussed that problem on discord some days ago.
I was stuck in the same place. This is not about the USB stick, it is a big which is Frank already aware of it.

And I hope he is spending nights and days to fix it... ;)

To make it short: we X5000 users have to wait for the fix.

In that case he might just download 3.19 and try that.

And wait for 3.21.......

3.19 definitely works!
But then he cannot use the latest Iris and Wayfarer versions since they require MorphOS 3.20!

@Primax

All right, thanks.

@Kronos
It's a Fujitsu 00Y21L hard drive and a ATI 9000 Pro graphics card. I took that one out and put in a HIS R7 250X (I know the simple 250, without X are not suppurted) but the system didn't boot with any of the cards.

@jcaps
Only one card in the system at a time. One connected via DVI the other one through HDMI to the monitor.

The old morphos version worked with the exact same hardware. I very stupidly used the same USB stick because I didn't have another one available. I deleted the working MorphOS version (I think it was 3.14 not sure) and wrote the new one to the same stick.

Thanks for all the replies

Older MorphOS versions are easy to find:
https://www.morphos-team.net/morphos-3.19-hybrid.hdimg

Quote:
I solved the problem following the instructions provided at the following link.
https://morph.zone/modules/newbb_plus/viewtopic.php?topic_id=14223&forum=11

@amigait10

Eh? What is solved there? Nothing. It is the same problem and he stucks there.

Quote:

No, that workaround is working for me.

It worked for me too, but to install MorphOS I had to remove the SD card where I installed OS4.1 and plug in a SATA DVD and boot from the DVD.
After installing MorphOS, I removed the DVD and re-installed the SD card with OS4.1.
My configuration is as follows:
X5000-20
PCI-e 16x Radeon RX 570 for OS4.1
PCI-e 4x Radeon Radeon X1950 Pro for MorphOS
SATA Port 0 SD OS4.1
SATA Port 1 SD MorphOS
If I remember correctly, reversing the SD card order in the SATA ports didn't work.
Sorry for my English, but I used a translator.

Hm, obviously I am blind... :(

Apart from the fact, that I did not have a DVD drive, I cannot see any workaround in the linked thread...?!

Anyway. I hope, Frank will find a solution soon for the USB way.

Quote:

https://morph.zone/modules/newbb_plus/viewtopic.php?forum=11&topic_id=14223&post_id=164386&viewmode=flat&sortorder=0&showonepost=1 - here Bruh

You need to enable debug as it slows down the initiation and then on some machines it helps to get it booted.