Thanks
Problem solved
I replaced the Radeon HD R7 with a Radeon RX 570 in the PCIe 16X slot
and everything works

Good to hear all is working.

Enjoy!

Hello
I try same configuration dual gpu
The first gpu for os4 are r9 280 3gb vram
The second gpu for Mos are 6570

6570 work om pcie 16x whit or whitout pcie adapatator

But on pcie 4x or 1x whit r9 280, 6570 are not initialised by MorphOS but Morphos start

Some body help my ?

Hi,

I have tested a few cards myself and work fine with or withouth hardware acceleration depending on the model of the card. For now i am using the RX570 in PCIeX16 slot for AmigaOS and X1950 as second GPU for Linux / MorphOS use.

I do have a monitor connected on each GPU, and running 3.17 with the latest fix from Bigfoot.

You could try (if you have one) another card to see if the problem exists..

I ave try whit all my gpu !!
Im wainting from x1950
The fix are on to the 3.17 or i need to download it ?

The fix is in 3.17, and should work with the X1950

Hello
I have receved the x1950 and all working dual boot working
I can bokt the computer whitout monitor conencted to the firest gpu board

Quote:

Good to hear all is working.
Have fun with the setup!

How are you using an X1950 in the X5000? I have one on the way but its an AGP card isnt it? I know it was working in a friends G5 Mac Pro so it cant be PCIE as far as I would remember.

> How are you using an X1950 in the X5000? I have one on the way but its
> an AGP card isnt it? I know it was working in a friends G5 Mac Pro so
> it cant be PCIE as far as I would remember.

The ATI/AMD R5xx series GPUs on the Radeon X1xxx series graphics cards are PCIe chipsets. That's what they speak natively. Some graphics card manufacturers put those PCIe chipsets on AGP cards, together with a RIALTO bridge chip (not to be confused with Intel's GPU announced recently) to translate between AGP and PCIe. That's what your friend used in his PowerMac G5, provided it had AGP slots. If it had PCIe slots (PowerMac11,2), he used a PCIe X1950 card without RIALTO chip.

Quote:

I am pretty sure my 2.0 G5 is an AGP slot with PCI Express slots. Guess I will be sticking with the G5 when the card he is sending me arrives and have to find another that fits in my X5000.

Quote:

I believe you're confusing PCI Express with PCI-X slots here.

Quote:

Good catch, I did mean to type PCI-X

Well damn.... The X1950 Pro AGP just came and I see it take 2X molex to power it. My G5 has only one and its in use by the DVD drive. I assume no way in hell this will power the card and the DVD if I split it three ways.

How have people used these cards in a G5?

On the PCI-E G5 there is a power connector for such large GPUs on the mainboard (upper left quarter of the board), I only had to get an adapter.

Perhaps there is a suitable power connector on the AGP G5 mainboard as well?

Quote:

AGP G5 doesn't have an additional power connector because the gfx card is supposed to draw power from AGP port itself (it's in AGP Pro standard with additional power connector for ADC cards). Of course if you use a standard PC gfx card (not a custom Mac one) it's of no use.

When I had an AGP G5 I used a Molex splitter to get 1 free Molex from a DVD drive and an adapter to convert one of the HDD power connectors from SATA power to second Molex.

I know people who just draw all the power from DVD Molex connector and it's supposed to work.

@acill i have one X1950 AGP (no mac version) and i put only one from DVD connector.. and working here

Quote:

I will have to play. I tried to split it off just the SATA power and its not booting. I may rig a small 2nd PSU and try that.

Quote:

Maybe the Enhancer Package offers another incompatible version:
https://amigaworld.net/modules/news/article.php?storyid=8783

Or maybe a more compatible..

Quote:

I don't know in what cases SFS on AmigaOS4 and MorphOS are incompatible, but they are compatible for sure in this case:

on my Pegasos2 I have both systems
- all disks I prepare only with MorphOS tool HDconfig, blocksize 512. Even the disks for AmigaOS4
- volumes primary used with AmigaOS are formated under AmigaOS
- volumes for MorphOS under MorphOS
- Morphos formated volumes are readable, writable, browsable, deletable also under AmigaOS4
- AmigaOS formated volumes are readable, writable, browsable, deletable under MorphOS

tested continuously for many years with various system versions

[ Edited by sailor 15.08.2022 - 20:11 ]

> Maybe the Enhancer Package offers another incompatible version:
> https://amigaworld.net/modules/news/article.php?storyid=8783
> Or maybe a more compatible..

AFAIK, that's still Strohmayer's old version (with modifications to make it compatible with the X5000).

"We are also pleased to have licenced Joerg Strohmayer's Amiga software for the Enhancer Software including new versions of SmartFileSystem, AmiDVD, PartitionWizard and DiskCache Library."
https://amigaworld.net/modules/news/article.php?storyid=7722

Does the
"Tweaked the PCI address mapping on the X5000 to accommodate a Radeon on the PCIE1 bus"
work with the X5000/40 ?
And should it work with Radeon Northern Island cards such as a Radeon HD6450 ?

Not getting the above combination to boot .

==================================================================================================

U-Boot molsen-2018-10-05 (Oct 05 2018 - 17:02:31)

CPU0: P5040, Version: 2.1, (0x82040021)
Core: e5500, Version: 1.2, (0x80240012)
Clock Configuration:
CPU0:2200 MHz, CPU1:2200 MHz, CPU2:2200 MHz, CPU3:2200 MHz,
CCB:800 MHz,
DDR:800 MHz (1600 MT/s data rate) (Asynchronous), LBC:50 MHz
FMAN1: 600 MHz
FMAN2: 600 MHz
QMAN: 400 MHz
PME: 400 MHz
L1: D-cache 32 KiB enabled
I-cache 32 KiB enabled
Reset Configuration Word (RCW):
00000000: 90e00000 00000000 acac9800 00440000
00000010: 44808c00 ff29a000 68000000 61000000
00000020: 00000000 00000000 00000000 0003000f
00000030: a0000000 00000000 00000000 00000000
Board: CYRUS
36-bit Addressing
I2C: ready
SPI: ready
DRAM: Initializing....using SPD
Detected UDIMM KHX1600C10D3/8G
Detected UDIMM KHX1600C10D3/8G
14 GiB left unmapped
16 GiB (DDR3, 64-bit, CL=10, ECC off)
DDR Controller Interleaving Mode: cache line
DDR Chip-Select Interleaving Mode: CS0+CS1

Local Bus Controller Registers
BR0 0xE0001001 OR0 0xFFF00010
BR1 0xE1001001 OR1 0xFFF00010
BR2 0x00000000 OR2 0x00000000
BR3 0x00000000 OR3 0x00000000
BR4 0x00000000 OR4 0x00000000
BR5 0x00000000 OR5 0x00000000
BR6 0x00000000 OR6 0x00000000
BR7 0x00000000 OR7 0x00000000
LBCR 0x40000000 LCRR 0x80010004
L2: 512 KiB enabled
Corenet Platform Cache: 2 MiB enabled
SERDES: bank 2 disabled
MMC: FSL_SDHC: 0
Board Revision 2210
MAC: 00:04:A3:6B:41:3A
MAC: 00:1E:C0:F8:1F:8A
EEPROM: NXID v0
PCIe1: Root Complex, x4 gen2, regs @ 0xfe200000
01:00.0 - 1002:67ff - Display controller
01:00.1 - 1002:aae0 - Multimedia device
PCIe1: Bus 00 - 01
PCIe2: Root Complex, x4 gen2, regs @ 0xfe201000
03:00.0 - 111d:8092 - Bridge device
04:01.0 - 111d:8092 - Bridge device
05:00.0 - 12d8:e111 - Bridge device
04:02.0 - 111d:8092 - Bridge device
07:00.0 - 1002:6779 - Display controller
07:00.1 - 1002:aa98 - Multimedia device
04:03.0 - 111d:8092 - Bridge device
04:08.0 - 111d:8092 - Bridge device
09:00.0 - 1102:0012 - Multimedia device
04:10.0 - 111d:8092 - Bridge device
PCIe2: Bus 02 - 0a
PCIe3: disabled
PCIe4: disabled
Looking for VGA
PINS: 0xfc000808
videoboot: Booting PCI video card bus 1, function 0, device 0
Begin BIOS POST
End BIOS POST
Setting VESA Mode
Found required VESA mode
About to set mode 279
About to get mode
Got mode 49431 (0xc117)
OK
XSize = 1024 YSize = 768 Base =0xe0000000
mmio_base = 0x80000000
bgx = 0xad55ad55 fgx = 0x0
In: serial
Out: serial
Err: serial
ID: NXID v0
SN: 116400085
UID: 4429431001910051c4afa080a0800000
Errata: ÿÿÿÿÿ ÿ
Build date: 2016/04/19 09:38:08
CRC: 19f7f358
SCSI: scanning bus for devices...
Found 0 device(s).
Net: Initializing Fman

MMC read: dev # 0, block # 56985, count 128 ...
Fman1: Uploading microcode version 106.1.0

MMC read: dev # 0, block # 56985, count 128 ...
Fman2: Uploading microcode version 106.1.0
Tuning PHY @ 3
Tuning PHY @ 7
FM1@DTSEC5, FM2@DTSEC5
USB0: USB EHCI 1.00
scanning bus 0 for devices... EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80008d80
EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80008d80
EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80008c80
3 USB Device(s) found
USB1: USB EHCI 1.00
scanning bus 1 for devices... EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80008d80
EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80008d80
EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80008c80
6 USB Device(s) found
EHCI timed out on TD - token=0x80008d80
EHCI timed out on TD - token=0x80008d80
SATA0 (3 Gbps)
SATA1 (No RDY)
scanning bus for devices...
Found 0 device(s).
X5000> usb reset
resetting USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80008d80
EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80008d80
EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80008c80
3 USB Device(s) found
USB1: USB EHCI 1.00
scanning bus 1 for devices... EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80008d80
EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80008d80
EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80008c80
EHCI timed out on TD - token=0x80008c80
6 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
EHCI timed out on TD - token=0x80008d80
EHCI timed out on TD - token=0x80008d80
X5000> bootmorphos
MorphOS boot loader version 1.10
Failed to scan partitions on device 1
Booting from HDIMG0
Trying to load "bootcyrusplus.img" from "HDIMG0:"...
Loaded "bootcyrusplus.img" from "HDIMG0:", booting...
152.800|
152.800|
152.801| ABox 1.30 (2.7.2018) © 1999-2022 by Ralph Schmidt, Emmanuel Lesueur, Teemu Suikki, Harry Sintonen
152.856| P50X0_InitIDE@0: Drive present
152.861| P50X0_InitIDE@1: Drive not present
152.896| Post-reset SATA delay hack
152.932| Post-reset SATA delay hack
152.986| P50x0 SATA Driver@0: PIO Mode 4
153.002| P50x0 SATA Driver@0: UDMA Mode 6
153.023| ide.device@0: ATA-HD ST2000DX001-1NS1 <DIRECT_ACCESS>
153.029| HandleInterrupt@0: Signature is now 0x00000000
153.034| HandleInterrupt@0: Signature update
153.038| HandleInterrupt@0: Phy ready
153.042| ide.device@0: Mount <DH1>
153.045| ide.device@0: Partition <DH1> DosType 0x53465300 BootPri 0
153.051| ide.device@0: Mount <DH2>
153.054| ide.device@0: Partition <DH2> DosType 0x53465300
153.059| ide.device@0: Mount <DH3>
153.062| ide.device@0: Partition <DH3> DosType 0x53465300
157.192| usbscsi.device@0: Mount <HDIMG0>
157.196| usbscsi.device@0: Partition <HDIMG0> DosType 0x444f5307 BootPri 15
157.367| Radeon: Failed to read BIOS ROM
157.370| InitBoard: breaking at CRTC2
157.374| InitBoard: skipping AtomBIOS_AsicInit
157.891| Radeon: Timeout while waiting for display controller to be idle
158.403| Radeon: Timeout while waiting for display line buffer to initialise

@spectre

When my x5000/20 was build at relec, they tested the machine with an r9 in the x16 slot and a 6570 in the x1 slot.
It wouldn't work. When they exchanged the 6570 for an x1950 it suddenly worked.

[ Edited by Mozzerfan 06.11.2022 - 23:41 ]

@Mozzerfan


Thanks.
It could be card ram size greater than 256MB then.
Had that issue with a X5000/20 with Linux years ago .
My FireMV pciex1 cards don't work with the dual card configuration
so I am out cards to try currently.

@spectre

FYI I currently use a Radeon rx550 in the x16 slot and a firemv 2250 in the pci x1 slot.
The firemv card first wasn't recognized by morphos, so it would display the boot screen forever.
I then sent an email to bigfoot and he added the device ids of the card to the radeon driver.
So now it works beautifully.