Hi all.
Does anyone know if mos 3.21 contains a fix for the bug in the x5000 sata driver.
I just installed mos 3.21, and i still have to disconnect my os4 sata ssd.
Thanks.

[ Edited by Mozzerfan 08.11.2026 - 15:25 ]

It does, afaik.
Are you sure you don't have a boot priority conflict? MorphOS can be told from which partition to boot with bd=DH0 for example. You of course have to make sure that your OS4 install doesn't have the same partition names as MorphOS.

Thanks Jaca.
I have a dual gfxcard setup.
With the os4sata SSD connected, I get morphos booting...
Then black screen.
Only with os4 SSD disconnected, morphos boots into 3.21

I tried setting the bootprio of the os4 drive to -1. It didn't help.
Also booting with BD parameter gives a black screen.

Sure it isn't trying to use the other graphics card? The SSD drive might just be changing the timing resulting in other card being picked up... hard to say without a serial log.

OK. Here is the serial log




U-Boot molsen-2018-10-05 (Oct 05 2018 - 17:02:05)

CPU0: P5020, Version: 2.0, (0x82200020)
Core: e5500, Version: 1.2, (0x80240012)
Clock Configuration:
CPU0:1995 MHz, CPU1:1995 MHz,
CCB:798 MHz,
DDR:665 MHz (1330 MT/s data rate) (Asynchronous), LBC:49.875 MHz
FMAN1: 498.750 MHz
QMAN: 399 MHz
PME: 399 MHz
L1: D-cache 32 KiB enabled
I-cache 32 KiB enabled
Reset Configuration Word (RCW):
00000000: 0c540000 00000000 1e1e0000 00000000
00000010: 44808c00 ff002000 68000000 45000000
00000020: 00000000 00000000 00000000 0003000f
00000030: a0000000 00000000 00000000 00000000
Board: CYRUS
36-bit Addressing
I2C: ready
SPI: ready
DRAM: Initializing....using SPD
Detected UDIMM VS2GB1333D3
Detected UDIMM VS2GB1333D3
Not enough bank(chip-select) for CS0+CS1 on controller 0, interleaving disabled!
Not enough bank(chip-select) for CS0+CS1 on controller 1, interleaving disabled!
2 GiB left unmapped
4 GiB (DDR3, 64-bit, CL=9, ECC off)
DDR Controller Interleaving Mode: cache line

Local Bus Controller Registers
BR0 0xE0001001 OR0 0xFFF00010
BR1 0xE1001001 OR1 0xFFF00010
BR2 0x00000000 OR2 0x00000000
BR3 0x00000000 OR3 0x00000000
BR4 0x00000000 OR4 0x00000000
BR5 0x00000000 OR5 0x00000000
BR6 0x00000000 OR6 0x00000000
BR7 0x00000000 OR7 0x00000000
LBCR 0x40000000 LCRR 0x80010004
L2: 512 KiB enabled
Corenet Platform Cache: 2 MiB enabled
SERDES: bank 2 disabled
MMC: FSL_SDHC: 0
Board Revision dead
MAC: 00:04:A3:6B:41:BF
MAC: 00:1E:C0:F8:04:56
EEPROM: NXID v0
PCIe1: Root Complex, x4 gen2, regs @ 0xfe200000
01:00.0 - 1002:699f - Display controller
01:00.1 - 1002:aae0 - Multimedia device
PCIe1: Bus 00 - 01
PCIe2: Root Complex, x4 gen2, regs @ 0xfe201000
03:00.0 - 111d:8092 - Bridge device
04:01.0 - 111d:8092 - Bridge device
05:00.0 - 12d8:e111 - Bridge device
04:02.0 - 111d:8092 - Bridge device
07:00.0 - 1b21:1080 - Bridge device
08:00.0 - 13f6:0111 - Multimedia device
04:03.0 - 111d:8092 - Bridge device
04:08.0 - 111d:8092 - Bridge device
0a:00.0 - 1002:719b - Display controller
0a:00.1 - 1002:71bb - Display controller
04:10.0 - 111d:8092 - Bridge device
PCIe2: Bus 02 - 0b
PCIe3: disabled
PCIe4: disabled
Looking for VGA
PINS: 0xfc000808
videoboot: Booting PCI video card bus 1, function 0, device 0
Begin BIOS POST
End BIOS POST
Setting VESA Mode
Found required VESA mode
About to set mode 279
About to get mode
Got mode 49431 (0xc117)
OK
XSize = 1024 YSize = 768 Base =0xe0000000
mmio_base = 0x80000000
bgx = 0xad55ad55 fgx = 0x0
In: serial
Out: serial
Err: serial
ID: NXID v0
SN: 116350018
UID: 44294310019100519c7ca080a0800000
Errata: UG
Build date: 2016/01/06 10:55:47
CRC: e866de70
SCSI: scanning bus for devices...
Found 0 device(s).
Net: Initializing Fman

MMC read: dev # 0, block # 56985, count 128 ...
Fman1: Uploading microcode version 106.1.0
Tuning PHY @ 3
Tuning PHY @ 7
FM1@DTSEC4 [PRIME], FM1@DTSEC5
USB0: USB EHCI 1.00
scanning bus 0 for devices... 6 USB Device(s) found
USB1: USB EHCI 1.00
scanning bus 1 for devices... 2 USB Device(s) found
SATA0 (3 Gbps)
SATA1 (3 Gbps)
scanning bus for devices...
Found 0 device(s).
MorphOS boot loader version 1.17
Failed to scan partitions on device 0
Booting from DH0
Trying to load "bootcyrusplus.img" from "DH0:"...
Trying to load "boot.img" from "DH0:"...
Loaded "boot.img" from "DH0:", booting...
18.099|
18.100|
18.101| ABox 1.30 (2.7.2018) 1999-2022 by Ralph Schmidt, Emmanuel Lesueur, Teemu Suikki, Harry Sintonen
18.238| P50x0 SATA Driver@0: PIO Mode 4
18.242| P50x0 SATA Driver@0: UDMA Mode 6

Please add 'ed=init initresident' to boot arguments and get the log again.

I suppose you mean I use the edebugflags option?

If so, here's the log



U-Boot molsen-2018-10-05 (Oct 05 2018 - 17:02:05)

CPU0: P5020, Version: 2.0, (0x82200020)
Core: e5500, Version: 1.2, (0x80240012)
Clock Configuration:
CPU0:1995 MHz, CPU1:1995 MHz,
CCB:798 MHz,
DDR:665 MHz (1330 MT/s data rate) (Asynchronous), LBC:49.875 MHz
FMAN1: 498.750 MHz
QMAN: 399 MHz
PME: 399 MHz
L1: D-cache 32 KiB enabled
I-cache 32 KiB enabled
Reset Configuration Word (RCW):
00000000: 0c540000 00000000 1e1e0000 00000000
00000010: 44808c00 ff002000 68000000 45000000
00000020: 00000000 00000000 00000000 0003000f
00000030: a0000000 00000000 00000000 00000000
Board: CYRUS
36-bit Addressing
I2C: ready
SPI: ready
DRAM: Initializing....using SPD
Detected UDIMM VS2GB1333D3
Detected UDIMM VS2GB1333D3
Not enough bank(chip-select) for CS0+CS1 on controller 0, interleaving disabled!
Not enough bank(chip-select) for CS0+CS1 on controller 1, interleaving disabled!
2 GiB left unmapped
4 GiB (DDR3, 64-bit, CL=9, ECC off)
DDR Controller Interleaving Mode: cache line

Local Bus Controller Registers
BR0 0xE0001001 OR0 0xFFF00010
BR1 0xE1001001 OR1 0xFFF00010
BR2 0x00000000 OR2 0x00000000
BR3 0x00000000 OR3 0x00000000
BR4 0x00000000 OR4 0x00000000
BR5 0x00000000 OR5 0x00000000
BR6 0x00000000 OR6 0x00000000
BR7 0x00000000 OR7 0x00000000
LBCR 0x40000000 LCRR 0x80010004
L2: 512 KiB enabled
Corenet Platform Cache: 2 MiB enabled
SERDES: bank 2 disabled
MMC: FSL_SDHC: 0
Board Revision dead
MAC: 00:04:A3:6B:41:BF
MAC: 00:1E:C0:F8:04:56
EEPROM: NXID v0
PCIe1: Root Complex, x4 gen2, regs @ 0xfe200000
01:00.0 - 1002:699f - Display controller
01:00.1 - 1002:aae0 - Multimedia device
PCIe1: Bus 00 - 01
PCIe2: Root Complex, x4 gen2, regs @ 0xfe201000
03:00.0 - 111d:8092 - Bridge device
04:01.0 - 111d:8092 - Bridge device
05:00.0 - 12d8:e111 - Bridge device
04:02.0 - 111d:8092 - Bridge device
07:00.0 - 1b21:1080 - Bridge device
08:00.0 - 13f6:0111 - Multimedia device
04:03.0 - 111d:8092 - Bridge device
04:08.0 - 111d:8092 - Bridge device
0a:00.0 - 1002:719b - Display controller
0a:00.1 - 1002:71bb - Display controller
04:10.0 - 111d:8092 - Bridge device
PCIe2: Bus 02 - 0b
PCIe3: disabled
PCIe4: disabled
Looking for VGA
PINS: 0xfc000808
videoboot: Booting PCI video card bus 1, function 0, device 0
Begin BIOS POST
End BIOS POST
Setting VESA Mode
Found required VESA mode
About to set mode 279
About to get mode
Got mode 49431 (0xc117)
OK
XSize = 1024 YSize = 768 Base =0xe0000000
mmio_base = 0x80000000
bgx = 0xad55ad55 fgx = 0x0
In: serial
Out: serial
Err: serial
ID: NXID v0
SN: 116350018
UID: 44294310019100519c7ca080a0800000
Errata: �����UG�
Build date: 2016/01/06 10:55:47
CRC: e866de70
SCSI: scanning bus for devices...
Found 0 device(s).
Net: Initializing Fman

MMC read: dev # 0, block # 56985, count 128 ...
Fman1: Uploading microcode version 106.1.0
Tuning PHY @ 3
Tuning PHY @ 7
FM1@DTSEC4 [PRIME], FM1@DTSEC5
USB0: USB EHCI 1.00
scanning bus 0 for devices... 6 USB Device(s) found
USB1: USB EHCI 1.00
scanning bus 1 for devices... 2 USB Device(s) found
SATA0 (3 Gbps)
SATA1 (3 Gbps)
scanning bus for devices...
Found 0 device(s).
X5000> usb reset
resetting USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 6 USB Device(s) found
USB1: USB EHCI 1.00
scanning bus 1 for devices... 2 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
X5000> bootmorphos EDEBUGFLAGS='init initresident'
MorphOS boot loader version 1.17
Failed to scan partitions on device 1
Booting from DH0
Trying to load "bootcyrusplus.img" from "DH0:"...
Trying to load "boot.img" from "DH0:"...
Loaded "boot.img" from "DH0:", booting...
78.865|
78.866|
78.866| ABox 1.30 (2.7.2018) � 1999-2022 by Ralph Schmidt, Emmanuel Lesueur, Teemu Suikki, Harry Sintonen
79.004| P50x0 SATA Driver@0: PIO Mode 4
79.008| P50x0 SATA Driver@0: UDMA Mode 6