• Order of the Butterfly
    Order of the Butterfly
    sailor
    Posts: 358 from 2019/5/9
    From: Central Bohemi...
    In Efika + graphics card, here is little insignificant progress ;-)

    I tested one friend's Radeon X600XT PCIe + bridge PEX8111, and here is the result:
    Code:
    EFIKA 5K2 Boot Strap [RELEASE BUILD] (c) 2002-2007 bplan GmbH (BUILD 20070122 84240)
    Running on CPU PVR: 0x80822014
    Running on system SVR: 0x80110022
    BIOS Code position: 0xFFF040D0
    Setup System Config... Done.
    Setup Memory Config... Done.
    Setup PCI... Done.
    Setup ATA... Done.
    Setup USB... Done.
    Setup ETH... Done.
    Setup AC97... Done.
    Testing 08000000 Bytes, Pass: 00000000 Failed: 00000000
    RAM TEST (fill random)... Done.
    cpu0: PowerPC,G2 CPUClock 396 Mhz BUSClock 132 Mhz (Version 0x8082,0x2014)
    channel 0 unit 0 : ata | WDC WD3200BEVE-00A0HT0 | 11.01A11
    ATA device not present or not responding
    EMULATION INT HANDLER ENTERED WITH:
    INT NO: 15

    EAX=0000 EBX=1111 ECX=2222 EDX=3333 ESP=0000 EBP=5555 ESI=6666 EDI=7777
    AX=4E08 BX=C605 CX=0003 DX=202A SP=6E3F BP=5555 SI=5EE2 DI=7777
    DS=C000 ES=BAD0 SS=C000 CS=F000 IP=FE15 NV UP -- PL ZR NA PE NC
    CS:IP = F4 FS=BAD4 GS=BAD5C6F4 C000 0244 3000 0000 01B4 ADC8 0200
    UNHANDLED INT 10 FUNCTION 0007 WITHIN EMULATION
    VM using 1457272 x86 cycles for GFX init
    Memory used before SYS_Init: 9MB


    ABox 1.30 (2.7.2018) © 1999-2018 by Ralph Schmidt, Emmanuel Lesueur, Teemu Suikki, Harry Sintonen
    PPC5200 ATA/ATAPI Driver@0: PIO Mode 4
    ide.device@0: ATA-HD WDC WD3200BEVE-0 <DIRECT_ACCESS>
    ide.device@0: Mount <DH0>
    ide.device@0: Partition <DH0> DosType 0x53465300 BootPri 0
    ide.device@0: Mount <DH1>
    ide.device@0: Partition <DH1> DosType 0x53465300
    Radeon: Failed to initialise Radeon DMA
    Radeon: Failed to allocate CCE DMA memory


    Serial debug result is the same as result from working cards: 9700PRO and 9200.
    X86 emulator seems to run an don't stuck (like with ATOMbios cards).
    But, unfortunatelly - no video output. Nor from OF nor from MorphOS.
    Tested with DVI and VGA.
    Any ideas?
    Maybe try PEX 8112 bridge, but I have no one.
    AmigaOS3: Amiga 1200
    AmigaOS4: Micro A1-C, AmigaOne XE, Pegasos II, Sam440ep, Sam440ep-flex, AmigaOneX1000
    MorphOS: Efika 5200b, Pegasos I, Pegasos II, Powerbook G4, Mac Mini, iMac G5, Powermac G5 Quad
  • »26.01.21 - 17:55
    Profile