• Butterfly
    Butterfly
    metatron
    Posts: 72 from 2011/11/18
    This is the output from the serial connector (115200 8n1):
    Quote:



    U-Boot 2015.a (May 16 2015 - 14:20:11)

    CPU: AMCC PowerPC 460EX Rev. B at 1100 MHz (PLB=220 OPB=110 EBC=110)
    No Security/Kasumi support
    Bootstrap Option H - Boot ROM Location I2C (Addr 0x52)
    Internal PCI arbiter enabled
    32 kB I-Cache 32 kB D-Cache
    Board: Sam460ex/cr, PCIe 4x + PCIe 1x
    I2C: ready
    DRAM: 2 GiB (ECC not enabled, 440 MHz, CL4)
    PCI: Bus Dev VenId DevId Class Int
    00 04 1095 3114 0106 00
    PCIE0: link is not up.
    PCIE1: successfully set as root-complex
    02 00 1002 71c7 0300 ff
    Net: ppc_4xx_eth0
    FPGA: Revision 03 (2010-10-07)
    SM502: not found
    PERMD2:not found
    VGA: 1
    VESA: OK

    Got past the basic MMU setup
    L2 cache enabled
    DCR 0x40: 0000e000
    DCR 0x41: 1000e000
    DCR 0x42: 00000000
    DCR 0x43: 00000000
    Calculated 0x80000000 bytes of RAM
    Board configured in PCI Express mode
    PIC initialised
    CPU Frequency: 1100.000MHz
    Filtered write of 0xffffffff to PCIX1 config space address 0x14
    Filtered read from PCIX1 config space address 0x14
    Filtered write of 0xffffffff to PCIX1 config space address 0x1c
    Filtered read from PCIX1 config space address 0x1c
    Filtered write of 0xffffffff to PCIX1 config space address 0x20
    Filtered read from PCIX1 config space address 0x20
    Filtered read from PCIX1 config space address 0x30
    Filtered write of 0xfffffffe to PCIX1 config space address 0x30
    Filtered read from PCIX1 config space address 0x30


    ABox 1.28 (02.05.2014) ▒ 1999-2014 by Ralph Schmidt, Emmanuel Lesueur, Teemu Sui kki, Harry Sintonen
    Driver_InitBoard: Channels = 4 UnitsPerChannel = 1
    PCI (S)ATA/ATAPI Driver@0: PIO Mode 4
    PCI (S)ATA/ATAPI Driver@0: UDMA Mode 5
    PCI (S)ATA/ATAPI Driver@1: PIO Mode 4
    PCI (S)ATA/ATAPI Driver@1: UDMA Mode 5
    sata.device@0: HL-DT-ST DVDRAM GH24NSC0 <CDROM>
    sata.device@1: ATA-HD SanDisk SDSSDHP1 <DIRECT_ACCESS>
    sata.device@1: Mount <DH0>
    sata.device@1: Partition <DH0> DosType 0x444f5307 BootPri 0
    sata.device@1: Mount <DH1>
    sata.device@1: Partition <DH1> DosType 0x53465300
    usbscsi.device@0: Mount <SDH0>
    usbscsi.device@0: Partition <SDH0> DosType 0x444f5307 BootPri 5
    !!! OpenScreen(): Could not find any valid modeids. No graphics card? !!!
    Hello, Ambient here. I couldn't open a screen so I'm trying to
    communicate through the serial port. Hopefully someone can see this.

    Please check the following:
    - working and supported graphics card
    - latest version of the boot.img kernel
    - booting from the correct device
    - driver installed in MOSSYS:Devs/Monitors

    If it still doesn't work, seek help on the MorphOS support mailing-lists
    or contact support@morphos-team.net




    [ Editiert durch metatron 07.07.2015 - 17:31 ]
  • »07.07.15 - 17:23
    Profile